Contact Form 
STANDARD BELT SELECTION GUIDE |
Standard belt material is stocked at Dorner, then cut & spliced at the factory for fast conveyor shipment. |
||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
  |
| 01 | FDA Accumulation | .063" (1.6) | Urethane | Polyester | 176°F (80°C) | Low | X | X | Good | Packaging, clean room & inspection | |
| 02 | General Purpose | .071” (1.8) | Urethane | Polyester | 212˚F (100˚C) | Med | X | X | Good | Most versatile belt offering | |
| 03 | FDA High Friction | .063” (1.6) | Urethane | Polyester | 176˚F (80˚C) | High | X | X | Good | Packaging, clean room & inspection | |
| 05 | Accumulation | .047” (1.2) | Urethane | Polyester | 212˚F (100˚C) | V-Low | X | X | Good | Accumulation of products | |
| 06 | Electrically Conductive | .063” (1.6) | Urethane | Polyester | 230˚F (110˚C) | Low | X | X | Good | Electronics Handling | |
| 08 | High Friction | .083” (2.1) | PVC | Polyester | 158˚F (70˚C) | V-High | X | Poor | Conveys up to 35˚ inclines* | ||
Note: See below for splice details. Plastic Clipper splice requires longer lead times. Belts with V-guiding may have a slight high spot or rib on the top surface. This rib would run longitudinally along the center of the belt.
Consult factory with applications for which this may cause interference.
*Incline varies due to factors like dust, fluids and part material.
*Incline varies due to factors like dust, fluids and part material.
Belt Splicing |
Finger Splice |
SPECIALTY BELT SELECTION GUIDE |
Specialty belt material is not stocked at Dorner and needs to be custom ordered for your special conveyor needs. |
||||||||
|---|---|---|---|---|---|---|---|---|---|
|
|
 |
|
|
|
|
|
|
|
| 50 | Heat Resistant | .05 (1.3) | Silicone | 356˚F (180˚C) | Low | Good | |||
| 53 | Translucent & Nosebar, Accumulation |
.02 (.51) | Urethane | 212˚F (100˚C) | V-Low | X | Good | Back Lit inspection & Very Small Product Transfer | |
| 54 | FDA Sealed Edge* | X | .06 (1.5) | Urethane | 176˚F (80˚C) | Low | X | Good | Packaging, clean room & inspection |
| 55 | FDA Sealed Edge* | X | .06 (1.5) | Urethane | 176˚F (80˚C) | High | X | Good | Packaging, clean room & inspection |
| 56 | Cut Resistant | X | .08 (2.1) | Urethane | 212˚F (100˚C) | Med | Good | Oily product release, Metal stamping | |
| 57 | Cut Resistant | X | .10 (2.5) | Nitrile | 176˚F (80˚C) | Med | Poor | Felt-like, dry metal stamping, glass & ceramic | |
| 58 | Cut Resistant | .06 (1.5) | Urethane | 176˚F (80˚C) | Low | V-Good | Cross-linked surface, Gold colored | ||
| 59 | Color Contrasting | X | .06 (1.5) | PVC | 158˚F (70˚C) | Med | Poor | Black colored, hides overspray from ink jet | |
| 60 | Color Contrasting | X | .06 (1.6) | Urethane | 176˚F (80˚C) | Low | X | Good | Green colored |
| 61 | Color Contrasting | X | .05 (1.2) | Urethane | 212˚F (100˚C) | Med | X | Good | Blue colored |
| 63 | Electrically Conductive | X | .05 (1.2) | Urethane | 140˚F (60˚C) | Low | Good | Static conductive, electronics handling | |
| 65 | Chemical Resistant | .05 (1.3) | Polypropylene | 250˚F (126˚C) | Low | X | V-Good | V-Good Cut resistance, excellent product release | |
| 66 | Chemical Resistant | X | .07 (1.7) | Polyester | 212˚F (100˚C) | Med | X | V-Good | Good Cut resistance, metal stamping apps |
Note: Plastic Clipper splice requires longer lead times. Belts with V-guiding may have a slight high spot or rib on the top surface. This rib would run longitudinally along the center of the belt.
Consult factory with applications for which this may cause interference.
* Not available on 1.75” (44) wide conveyors.
* Not available on 1.75” (44) wide conveyors.