Home About Dorner Contact Us Distributors TradeshowsSite Map

 
Dorner Performance Newsletter


 

DORNER MFG. CORP.
975 Cottonwood Ave
P.O. Box 20
Hartland, WI 53029 USA

INSIDE THE USA
TEL: 800.397.8664
FAX: 800.369.2440

OUTSIDE THE USA
TEL: 262.367.7600
FAX: 262.367.5827

6200 SERIES CONVEYORS: Belting



STANDARD BELT SELECTION GUIDE Standard belt material is stocked at Dorner,
then cut & spliced at the factory for fast conveyor shipment.
01 A1 1A FDA Accumulation .063" (1.6) Urethane Polyester 176°F (80°C) Low X X   Good Packaging, clean room & inspection
02 A2 2A General Purpose .071” (1.8) Urethane Polyester 212˚F (100˚C) Med X X   Good Most versatile belt offering
03 A3 3A FDA High Friction .063” (1.6) Urethane Polyester 176˚F (80˚C) High X X   Good Packaging, clean room & inspection
05 A5 5A Accumulation .047” (1.2) Urethane Polyester 212˚F (100˚C) V-Low X X   Good Accumulation of products
06   6A Elecrtically Conductive .063” (1.6) Urethane Polyester 230˚F (110˚C) Low   X X Good Electronics Handling
08 A8 8A High Friction .083” (2.1) PVC Polyester 158˚F (70˚C) V-High   X   Poor Conveys up to 35˚ inclines*
Note: See below for splice details. Plastic Clipper splice requires longer lead times. Belts with V-guiding may have a slight high spot or rib on the top surface. This rib would run longitudinally along the center of the belt. Consult factory with applications for which this may cause interference.
*Incline varies due to factors like dust, fluids and part material.

 

Belt Splicing

Finger Splice
All belts are available with a standard Thermoformed finger splice. This splice makes the belt continuous and is virtually undetectable. Splice bonding methods vary by belt type. Consult factory for details.

Plastic Clipper*
An optional plastic clipper splice is available for quick removal of belts or when conveyors are installed in tight spaces. The clipper does not protrude above the belt surface.

Metal Clipper*
An optional metal clipper splice is also available for quick removal of belts or when conveyors are installed in tight spaces.
*See belt charts for compatibility. Not for use with 6200 Series Gang Drive and 6200 Series with bottom wiper option.

 

SPECIALTY BELT SELECTION GUIDE Specialty belt material is not stocked at Dorner
and needs to be custom ordered for your special conveyor needs.
54 F4 4F FDA Sealed Edge* X .06 (1.5) Urethane 176˚F (80˚C) Low X Good Packaging, clean room & inspection
55 F5 5F FDA Sealed Edge* X .06 (1.5) Urethane 176˚F (80˚C) High X Good Packaging, clean room & inspection
56   6F Cut Resistant X .08 (2.1) Urethane 212˚F (100˚C) Med   Good Oily product release, Metal stamping
57   7F Cut Resistant X .10 (2.5) Nitrile 176˚F (80˚C) Med   Poor Felt-like, dry metal stamping, glass & ceramic
59 F9 9F Color Contrasting X .06 (1.5) PVC 158˚F (70˚C) Med   Poor Black colored, hides overspray from ink jet
60 G0 0G Color Contrasting X .06 (1.6) Urethane 176˚F (80˚C) Low X Good Green colored
61 G1 1G Color Contrasting X .05 (1.2) Urethane 212˚F (100˚C) Med X Good Blue colored
63   3G Electrically Conductive X .05 (1.2) Urethane 140˚F (60˚C) Low   Good Static conductive, electronics handling
64   4G High Friction X .17 (4.4) PVC 194˚F (90˚C) V-High   Poor Dark Green colored, rough top surface,
product cushioning, incline / decline apps
66   6G Chemical Resistant X .07 (1.7) Polyester 212˚F (100˚C) Med X V-Good Good Cut resistance, metal stamping apps
67   7G Low Friction Cleated X .06 (1.6) Polyester 212˚F (100˚C) n/a X Good Excellent product release, consult factory for part
number and how to specify low friction
Note: Plastic Clipper splice requires longer lead times. No Metal Clipper Splice on belts over 12” (305) wide.
Note: Belts with V-guiding may have a slight high spot or rib on the top surface. This rib would run longitudinally along the center of the belt.
Consult factory with applications for which this may cause interference.
* 12” (305) wide conveyor maximum. ** Not available in 2” (51) or smaller widths.

 

STANDARD CLEATS

* Maximum 20” (508) cleat spacing for 18” and wider conveyors with lengths greater than 7’ (2134)
** 18” and wider conveyors have a maximum length of 7’ (2134)

Base Belt Material: .055 (1.4) thick, high friction FDA approved urethane, 176˚F (80˚C) maximum part temperature.
See Specialty Belt 67 for low friction base belt material.

Note: Minimum cleat spacing is approximately 2” (51). Consult Factory.

 

Cleat Spacing

  1. Refer to Formulas below.
  2. Use formula 1 to determine the approximate number of cleats required based upon the desired cleat spacing. Since a partial cleat cannot be used, round the number of cleats up or down.
  3. Use formula 2 to get the cleat space reference for the conveyor part number.

 

PART NUMBER REFERENCE

 

Back to top