Contact
Form 7200 SERIES CONVEYORS: Flat Belt End Drive
Specifications:
- Self-aligning stainless steel sealed bearings
with FDA approved solid lubricant - 11 gauge stainless steel roll formed frame
- Belt widths: 1.75” (44) to 18” (457)
- Conveyor lengths: 2’ (610) to 18’ (8,486)
- 1.5” (38) bottom of frame to top of belt
- 12mm diameter integral drive shaft
- The 1.25” (32) diameter drive pulley turns approximately
4.25” (108) of belt per revolution - 2’ (610) minimum, 18’ (8,486) maximum conveyor lengths
- Loads up to 60 Lbs* (27 Kg)
- Belt speeds up to 264 ft/min. (81 M/min.)
- Metric fasteners
- Complete stainless steel construction
- Washdown rated gearmotors and controls
models available
Features/Benefits:
- Wedge-Lok system for impact protection
- Pre-engineered conveyor and accessory solutions for fast delivery
- Streamlined design fits where other conveyors do not
- Quick 5 minute belt change for increased uptime
- 304 stainless steel frame, head and tail plates are polished to a #4 finish
- Quick clamp rail for easy mounting of bolt-on accessories
- Rack and pinion for fast single point belt tensioning
- V-Groove frame with guided belt ensures accurate tracking
- Optional 1/4” (6mm) thick bottom wiper
- A variety of FDA approved belting to meet application needs
- Lengths in .12” (3) increments
- Low profile, single piece frame for quick, easy cleaning
| The bearings are engineered for tough conditions, 24/7 operations, full rated load, full rated speed, and once per day cleaning with Low Pressure (100 psi max) soap and water. When the conveyors are properly applied and maintained the bearings will provide a minimum of 1 year of service. |
New Features:
-
See the Belt Section (pg. 180) for the new belt options
-
Quick Release plastic clipper splice for easy cleaning
-
Fully Encased FDA belts for Added sanitary protection
Change Belts in Less than 5 Minutes! |
||
 |
 |
 |
Loosen fasteners and |
Remove old belt and replace. |
Adjust tension on new belt, |
 |
 |
Perforated Bedplate Option |
Optional Bottom Wiper |
| STANDARD SIZES | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Conveyor Width Reference | 02 | 03 | 04 | 05 | 06 | 08 | 10 | 12 | 18 |
| Conveyor Belt Width (W) | 1.75” (44) |
2.75” (70) |
3.75” (95) |
5” (127) |
6” (152) |
8” (203) |
10” (254) |
12” (305) |
18” (457) |
| Conveyor Length Reference | 0200 | 0001 increments up to... | 1800 | ||||||
| Conveyor Length (L) | 2’ (610) | .12” (3) increments up to... | 18’ (5,486) | ||||||
Note: Lengths 13’ to 18’ available in widths 6” to 18” only.
Notes:
- Conveyor load capacity depends on conveyor size, incline, motor position, accumulated loads and other factors. See Performance Charts / Data for details.
- Order gearmotor mounting packages and gearmotors separately - see Mount Packages and Gearmotors. For support stands and accessories - see Support Stands and Accessories.
- Dimensions are represented in inches, feet, and (millimeters).
- Due to the wide variety of drive set-ups and applications, point of installation guarding is the responsibility of the end user.
- Conveyors longer than 12’ (3658mm) will be constructed using a multiple piece frame. Consult factory for locations of these frame joints. It is recommended that each frame joint be supported by a stand or other means.