Home About Dorner Contact Us Distributors Tradeshows Site Map

 
Dorner Performance Newsletter


 

DORNER MFG. CORP.
975 Cottonwood Ave
P.O. Box 20
Hartland, WI 53029 USA

INSIDE THE USA
TEL: 800.397.8664
FAX: 800.369.2440

OUTSIDE THE USA
TEL: 262.367.7600
FAX: 262.367.5827

7600 SERIES CONVEYORS: Belting



STANDARD BELT SELECTION GUIDE

Standard belt material is stocked at Dorner,
then cut & spliced at the factory for fast conveyor shipment.
01 A1 1A FDA Accumulation .063" (1.6) Urethane Polyester 176°F (80°C) Low   X X   Good Packaging, clean room & inspection
02 A2 2A General Purpose .071” (1.8) Urethane Polyester 212˚F (100˚C) Med   X X   Good Most versatile belt offering
03 A3 3A FDA High Friction .063” (1.6) Urethane Polyester 176˚F (80˚C) High   X X   Good Packaging, clean room & inspection
05 A5 5A Accumulation .047” (1.2) Urethane Polyester 212˚F (100˚C) V-Low   X X   Good Accumulation of products
06   6A Elecrtically Conductive .063” (1.6) Urethane Polyester 230˚F (110˚C) Low     X X Good Electronics Handling
08 A8 8A High Friction .083” (2.1) PVC Polyester 158˚F (70˚C) V-High     X   Poor Conveys up to 35˚ inclines*
09     Nosebar High Friction .055 (1.4) Urethane Polyester 212˚F (100˚C) High X X     Good Nosebar Applications
Note: See below for splice details. Plastic Clipper splice requires longer lead times. No Metal Clipper Splice on belts over 48” (1219) wide.
*Incline varies due to factors like dust, fluids and part material. **Metal Clipper splices are not sanitary.

 

Belt Splicing

Finger Splice
All belts are available with a standard Thermoformed finger splice. This splice makes the belt continuous and is virtually undetectable. Splice bonding methods vary by belt type. Consult factory for details.

Plastic Clipper*
An optional plastic clipper splice is available for quick removal of belts or when conveyors are installed in tight spaces. The clipper does not protrude above the belt surface.

Metal Clipper*
An optional metal clipper splice is also available for quick removal of belts or when conveyors are
installed in tight spaces.
(Not Sanitary)
*See belt charts for compatibility. Not for use with 7600 Series Nose Bar Transfer and 7600 Series with bottom wiper option.

 

SPECIALTY BELT SELECTION GUIDE

Specialty belt material is not stocked at Dorner
and needs to be custom ordered for your special conveyor needs.
54 F4 4F FDA Sealed Edge .06 (1.5) Urethane 176˚F (80˚C) Low   X Good Good Packaging, clean room & inspection, wet environment
55   5F FDA Sealed Edge .06 (1.5) Urethane 176˚F (80˚C) High   X Good Good Packaging, clean room & inspection, wet environment
56   6F Cut Resistant .08 (2.1) Urethane 212˚F (100˚C) Med.     Good Poor Oily product release, Metal stamping
57   7F Cut Resistant .10 (2.5) Nitrile 176˚F (80˚C) Med.     Poor Poor Felt-like, dry metal stamping, glass & ceramic
59 F9 9F Color Contrasting .06 (1.5) PVC 158˚F (70˚C) Med.     Poor Poor Black colored, hides overspray from ink jet
60 G0 0G Color Contrasting .05 (1.2) Urethane 212˚F (100˚C) Low X X Good Poor Green colored, Nosebar
61 G1 1G Color Contrasting .05 (1.2) Urethane 212˚F (100˚C) Low X X Good Poor Blue colored, Nosebar
63   3G Electrically Conductive .05 (1.2) Urethane 140˚F (60˚C) Low     Good Poor Static conductive, electronics handling
64   4G High Friction .17 (4.4) PVC 194˚F (90˚C) V-High     Poor Poor Dark Green colored, rough top surface,
product cushioning, incline / decline apps
66   6G Chemical Resistant .07 (1.7) Polyester 212˚F (100˚C) Med.   X V-Good Poor Good Cut resistance, metal stamping apps
67   7G Low Friction Cleated .06 (1.6) Polyester 212˚F (100˚C) n/a   X Good Poor Excellent product release, consult factory for part
number and how to specify low friction
68 G8   FDA Encased* .08 (2) Urethane 212˚F (100˚C) Low   X Good V-Good Urethane Enclosed for added sanitary protection
69 G9   FDA Encased* .08 (2) Urethane 212˚F (100˚C) High   X Good V-Good Urethane Enclosed for added sanitary protection
70     Solid Urethane .10 Urethane 212˚F (100˚C) Med.   X Good V-Good USDA Approved, wet applications
71     High Release Cover .07 (1.7) Urethane 212˚F (100˚C) Low   X Good Poor Raw dough or sticky food product
72     Nosebar Low Friction .05 (1.2) Urethane 212˚F (100˚C) Low X X Good Poor Nosebar Applications
No Metal Clipper Splice on belts over 48” (1219) wide.
* Not available in 2” (51) wide.
**Metal Clipper splices are not sanitary.

 

STANDARD CLEATS

* = Maximum 7’ conveyor length for 18” and wider conveyors

** = Maximum 20” (508) cleat spacing for 7’ and longer conveyors

 

Note: Minimum cleat spacing is approximately 2” (50). Consult Factory.

Standard Cleated Belting
A High Friction .055 (1.4) Urethane 1.0 (25) Urethane 176 (80) Yes Good Poor I
B High Friction .055 (1.4) Urethane 1.57 (40) Urethane 176 (80) Yes Good Poor II
C High Friction .055 (1.4) Urethane 2.36 (60) Urethane 176 (80) Yes Good Poor III
G High Friction .055 (1.4) Urethane 0.43 (11) Urethane 176 (80) Yes Good Poor IV
J Low Friction .06 (1.6) Urethane 1.0 (25) Urethane 212 (100) Yes Good Poor I
K Low Friction .06 (1.6) Urethane 1.57 (40) Urethane 212 (100) Yes Good Poor II
L Low Friction .06 (1.6) Urethane 2.36 (60) Urethane 212 (100) Yes Good Poor III
M Low Friction .06 (1.6) Urethane 0.43 (11) Urethane 212 (100) Yes Good Poor IV

 

Cleat Spacing

  1. Refer to Formulas below.
  2. Use formula 1 to determine the approximate number of cleats required based upon the desired cleat spacing. Since a partial cleat cannot be used, round the number of cleats up or down.
  3. Use formula 2 to get the cleat space reference for the conveyor part number.

 

Part Number Reference

SPECIALTY CLEATED BELTING

* = Maximum 7’ conveyor length for 18” and wider conveyors

** = Maximum 20” (508) cleat spacing for 7’ and longer conveyors

 

Note: Minimum cleat spacing is approximately 2” (50). Consult Factory.

Specialty Cleated Belting
N Sealed Edge .06 (1.5) Urethane .79 (20) Urethane 176 (80) Yes Good Good I
P Sealed Edge .06 (1.5) Urethane 1.57 (40) Urethane 176 (80) Yes Good Good II
Q Sealed Edge .06 (1.5) Urethane 2.36 (60) Urethane 176 (80) Yes Good Good III
R Encased .08 (2) Urethane .79 (20) Urethane 212 (100) Yes Good Very Good I
S Encased .08 (2) Urethane 1.57 (40) Urethane 212 (100) Yes Good Very Good II
T Encased .08 (2) Urethane 2.36 (60) Urethane 212 (100) Yes Good Very Good III
U Standard .06 (1.5) Urethane 1.18 (30) Urethane 176 (80) Yes Good Poor IV
V Standard .06 (1.5) Urethane 1.97 (50) Urethane 176 (80) Yes Good Poor IV
W Sealed Edge .06 (1.5) Urethane 1.18 (30) Urethane 176 (80) Yes Good Good IV
X Sealed Edge .06 (1.5) Urethane 1.97 (50) Urethane 176 (80) Yes Good Good IV
Y Encased .06 (1.5) Urethane 1.18 (30) Urethane 176 (80) Yes Good Very Good IV
Z Encased .06 (1.5) Urethane 1.97 (50) Urethane 176 (80) Yes Good Very Good IV

Cleat Spacing

  1. Refer to 7600 Series Formulas above.
  2. Use formula 1 to determine the approximate number of cleats required based upon the desired cleat spacing. Since a partial cleat cannot be used, round the number of cleats up or down.
  3. Use formula 2 to get the cleat space reference for the conveyor part number.

Part Number Reference

 

Back to top